BOLT Black Ops
Free Gift

Product Description

Now Shipping 4 , 5 and 6 inch versions  ! 

This is our new Black Ops race/proximity frame designed to be flown anywhere and still beat the opposition on race day. 

Besides being light weight, this frame has ultra low surface area for reduced wind resistance and high speed performance.  In fact it has only marginally more surface area than our ridiculously fast Race series.

Key features are:
Symmetrical motor locations with 4" , 5" and 6'" variants
Significantly lower weight than your standard black out style frame yet smaller and stronger:

  •    4in - 105 grams 
  •    5in - 112 grams
  •    6in - 118 grams

Extensive integrated CF bumper protection system, top and bottom, front and rear.
Lower 30mm profile for strength
Innovative structural system and component layout
High quality components including 7075 aluminium standoffs and titanium fasteners.
Full compatibility with the Race series 180, 210 and 225. In other words, you can swap base plate systems and arms between the Black Ops and Race series and in any size (BO4, BO5, BO6, Race180, Race210 and Race225).  

Further information on the frame design is contained in the thread on rcgroups.

Package Contents

Top Plate - 2.0mm
Upper Bottom Plate - 1.5mm
Lower Bottom Plate - 2.0mm
Top Front Bumper - 1.5mm
Top Rear Bumper - 1.5mm
Bottom Front Bumper - 4.0mm
Bottom Rear Bumper - 4.0mm

Afro Mini PDB #
Die cut neoprene foam rubber battery pad for the top plate

Arm Choice
Arms are removable and interchangeable with other arm sizes:
  4in Arms - 4mm thick and tapers to 14mm at narrowest point
  5in Arms - 4mm thick and tapers to 16mm at narrowest point
  6in Arms - 4mm thick and tapers to 18mm at narrowest point

Race Screw Kit
M3x30 7075 Orange Aluminum Standoffs - 5pcs
M3x12mm Hex Button Titanium Screw - 10pcs (top standoffs)
M3x10mm Nylon Black Hex (female - female) - 4pcs (customizing your FC stack)
M3x6mm Nylon Black Hex button machine screw - 5pcs (customizing your FC stack)
M3x8mm Nylon Black Hex button machine screw - 5pcs (customizing your FC stack)
M3x12mm Nylon Black Hex button machine screw - 5pcs (customizing your FC stack)
M3x1mm Nylon black washers - 20pcs (customizing your FC stack)
M3 Alu orange countersunk washers - 10pcs (use on all standoffs, especially top front)

Bottom Plate Screw Kit
M3x12 Stainless Steel Hex Button (black) - 15pcs (arm screws)
M3x14 Stainless Steel Hex Button (black) - 5pcs  (Bottom standoffs)
M3 Alu Nylon Lock Nut (Black) - 15pcs (arms screws)
M3x14mm Nylon Black Phillips button machine screw - 5pcs (customising your FC stack)

Pad Kit
Small black zip tie (same as other kit) 1.8x100mm - 10pcs
Large black zip tie (same as other kit) 35x350mm - 4pcs
3M double sided tape - 1.2mmx20mmx100mm - 1pc

Optional Extras+

Foam pad for bottom of frame
Custom XT60 PDB
Rear LEDs - High luminosity CREE LED in red, green and blue.
Four point FPV camera mount
Motor mount screw kits

The frame does not include motor mount screws or washers. We recommend alu hex cap screws and alu washers to mount your motors.  The motor mount options include 20 alu screws and 20 alu countersunk washers.

Build Comments

As these vertical CF plates are integral to the design, we have kept the tolerances as tight as we can. Accordingly, some sanding of the tabs for the vertical plates may be required to fit into the slots. Please avoid oversanding for a sloppy fit. Always include the vertical plates and bumpers in your build, they are a key structural design feature.  

The battery strap MUST go around the entire frame body and not just the top plate.  This is a key design feature which clampts the two plates togther with the vertical plates.  We recommend the longer BOLT battery straps (30cms) for this reason. 

Recommended Components

All electronics, wiring, motors and props are not included and can be purchased separately. Please note that this quad is specifically designed to take a 25mm mini cam (eg. HS1177) or the micro version.